Dealamanjaro: Hitachi 35 pc. Impact Rated Torsion Bit Set

September 6th, 2011 by Jim German Leave a reply »

I’m constantly in need of more driver bits, either from them breaking or more often, getting lost.  It’s therefore always great when a nice set  comes along for dirt cheap.  Sears is selling this Hitachi 35 piece set for just $7.50.  Its a nice little set with a few less common bits like square drive and torx in addition to a bunch of Phillips bits.   Best part is they are all impact rated so they’re good to go in all applications.

Source: Sears

Advertisement

11 comments

  1. Lamar Lein says:

    I intended to create you that little word to thank you over again about the great
    secrets you’ve shared here.

  2. Cazare Ieftina Poiana Brasov

    Hello! This is my first comment here so I just wanted to give a quick shout out
    and tell you I genuinely enjoy reading your posts.

    Can you suggest any other blogs/websites/forums that
    deal with the same subjects? Thanks a ton!

  3. Wow that was strange. I just wrote an incredibly long comment
    but after I clicked submit my comment didn’t show up.

    Grrrr… well I’m not writing all that over again. Regardless, just wanted to say wonderful blog!

    • Perchuhi says:

      I have a MM1110, the UK version of the MM10. I’ve had it for 3 4 years and it’s been great. Recently it’s been an unrlieable starter and now it shows only Operating System not found’. I took it to a repair shop and they said It needs a new drive’ but they failed to find one.I’ve replaced the drive, the Bios see’s it and the drive spins but it will not boot from the USB. I have a CD drive which starts spinning when I boot the laptop but the boot screen goes to’Operating System not found’ and the CD stops. This means I’m not able to install XP on the new disk. I’ve tried a USB key but I get Operating System not found’ again. I’ve tried various permutations with the bios with no success and the LAN PXE looks tough.Any Ideas?

    • Ayato says:

      Very accurate post on the lntamitiois of competitive information. I’ve seen exactly the same thing: embellishments, inaccurate information, hiding one’s own shortcomings, It becomes the tragedy of the blind (poorly informed partners) leading the blind (customers who don’t know what they want).Unfortunately, I don’t see an easy way out of this. To me, the nature of the channel relationship model bigger discounts for larger amount of business means that every partner eventually gravitates to one or another vendor. No matter how much Cisco one may know, if the day-to-day is based on Juniper (or HP or ) things will get stale. At some point, there is little opportunity to become a trusted advisor’ who is truly independent AND equally knowledgeable on multiple platforms at the same time.Going back to your point, I think we need to realize that failure’ and success’ will mean different things to vendors, partners and customers, even individuals. The current model of FUD based on incomplete competitive information’ is just a reflection of that.Sorry for the dispiriting thoughts. Better to acknowledge the issues so as to understand how to handle them

    • Blicks says:

      Hi Marcus. You have a keen eye to notice that. I had a preoblm with that footage I did not realize until after everything was glued up. Video 17 Entertainment Center Project has some good shots of the Domino. Dominos are solid wood slip tenons. Biscuits are not even in the same arena as far as strength. I know they are in S.A. because someone I correspond with from there is fully decked out with Festool. Need to check on comments being disabled on #5. Thanks for heads up. Keep in Touch. Allan

    • Ong says:

      My General Model 350 came with both. And both worked well for some atppicalions, but I do so many operations on the saw other than panel cuts or straight rips that I finally just went back to the way I learned. I raise the blade into the workpiece fairly often so the riving knife interfered, and I cut a lot of tenons and dovetails with the pieces standing on end so the guard was always in the way. I do make blade shrouds quit often for certain operations. I just stay away from the blade

    • Hey Nick,Thanks for the tutorial.What’s the render pass that shows greyscale shadows before the final pass is applied?Also, I have a fun question. How would you make a simple glowing object that casts light onto nearby objects.For instance, how would you make one of the balls in your example glow like a light bulb?Cheers.

  4. Alongside her, Lord Ganesha can be worshiped on Dipawali or Diwali, as he may be
    the one who is worshiped before starting worthwhile task.

  5. What’s up colleagues, its impressive article about teachingand fully defined, keep
    it up all the time.

Trackbacks /
Pingbacks

  1. garden state mall in elizabeth

Leave a Reply